When a line lets go behind drywall, every minute adds gallons to the damage. Close the main valve, call Water Heater Repairer, and a real person will connect you with a licensed and insured independent plumber close by, and a drying contractor if the water spread.
Every burst line creates two problems, the broken pipe itself and the soaked structure around it. We coordinate both so you are not juggling separate calls while the ceiling sags.
Pipe work inside walls touches code, so calls are routed to licensed and insured independent plumbers. Ask to see the license on arrival and check it with your state board.
A spraying line inside a finished wall gets priority over a slow drip under a sink. Arrival is often quick, depending on your location and how many freeze calls are stacked up that night.
You get a written, flat-rate quote for the repair and any wall access before anything gets cut. You know the number before the first tool comes out.
Plenty of the plumbers we route to bring acoustic listening gear and a thermal camera. That means smaller access holes and less guessing about where the split actually is.
Freeze breaks, corroded galvanized runs, cracked CPVC fittings, and slab leaks all come through this line. Tell the dispatcher what the pipe looks like and where it runs, and we match you with someone who works on that material every week.
Once water has run into ceilings, insulation, or flooring, the pipe repair alone does not end the problem. A drying contractor with moisture meters, air movers, and dehumidifiers can be sent so the cavity dries out before the wall is patched. Closing a wet wall is how small leaks turn into mold calls months later.
The right repair depends on what the pipe is made of, where it runs, and why it failed.
Pipes running through outside walls, vented crawlspaces, and attics are the first to freeze. The ice pushes pressure toward a closed fixture until the pipe splits, and the leak usually shows up once it thaws.
Type M copper has a thinner wall than Type L, so it tends to split and pinhole sooner. The fix is cutting back to clean pipe and joining it with a sweated or press fitting.
PEX itself flexes, yet the crimp rings and expansion fittings are where freeze damage shows up. CPVC turns brittle with age and heat, and old fittings crack if you so much as bump them.
A warm patch on tile or a water meter still moving with everything off usually means the leak is under the slab. Acoustic detection and thermal imaging pin it down, then you weigh a spot repair against a reroute through walls or attic.
Galvanized steel rusts from the inside, narrowing flow until a threaded joint finally lets go. Fixing one joint on a corroded system tends to stress the next weakest point.
Braided supply hoses on toilets, faucets, and washers can rupture at full line pressure with no warning. A relief valve on the water heater that drips or dumps water needs a look too.
Four steps, and you talk to a person at every one of them.
The dispatcher helps you locate the main valve and decide whether to shut off breakers near the water. Then we ask about the pipe material, the location, and whether any ceiling is sagging.
We route the job to a nearby licensed plumber who carries stock for copper, PEX, and CPVC repairs. If water spread past the leak area, a water damage contractor can be scheduled right behind them.
The plumber traces the break, often with a thermal camera or acoustic detector, and checks the run for other weak spots. A written, flat-rate quote comes before any drywall is cut.
The permanent repair goes in, the line is pressure tested, and the plumber watches the joint under full pressure before closing anything up. Ask about the contractor's own written workmanship warranty before they leave.
Push-to-connect fittings are great at two in the morning because they go on wet and stop the water fast. Most plumbers treat them as temporary inside a closed wall, and come back to sweat or press a permanent joint once things dry out.
Close the main valve, then call and we will route a local licensed plumber to you.
A pipe in the outside wall of our laundry room froze and split during the first cold snap. The dispatcher talked me through finding the main, and the plumber replaced the split copper that same morning. He also showed me the Type M pipe and explained why it went first.
Our water bill doubled and the hallway tile felt warm. They found the hot line leaking under the slab with an acoustic detector and a heat camera. We got two written prices, spot repair or reroute, and he explained both without pushing.
Water came through the dining room ceiling from an upstairs bathroom supply line. The plumber fixed the line and a water damage contractor showed up after to dry the ceiling and floor. Having both lined up from one call saved me a long night of searching.
A tenant in one of my rentals reported a cracked CPVC fitting under the kitchen sink. The plumber replaced it, then showed me two more fittings that crumbled when he touched them. I got a written quote to replace the whole run and time to think it over.
Shut off the main water valve, then switch off breakers for any circuits near the water. Open a lower faucet to drain the lines, move valuables, and call so a plumber can head your way.
Open the faucet the pipe feeds and warm the section slowly with a hair dryer, heat lamp, or space heater. Skip the torch entirely, because open flame starts wall fires and can burst the pipe with steam.
Many are rated for permanent use, but plenty of plumbers treat them as temporary inside a closed wall. Ask the plumber whether a sweated or press fitting makes more sense before the drywall goes back.
Acoustic leak detectors pick up the hiss of escaping water, and thermal imaging shows cool or warm patches where it spreads. Together they usually narrow the access hole to a small, patchable opening.
One leak on otherwise healthy pipe is usually a good case for a spot repair. Repeated leaks or aging copper tend to point toward a reroute so you are not breaking concrete again next year.
Drip faucets on exterior walls during deep cold and leave cabinet doors open for heat. Insulate exposed runs and add heat tape where pipes pass through cold crawlspaces, starting with the spots the plumber flags.
We route calls to independent plumbers working all over South Houston, from older neighborhoods with galvanized lines to newer builds plumbed in PEX. Surrounding suburbs are part of the coverage, including zip codes like 77587.
Older homes near the center of town tend to have galvanized mains and thin copper branch lines, which is where pinhole leaks and corroded threads show up. Newer subdivisions are mostly PEX or CPVC, so blown crimp fittings and cracked elbows top the list there. Give the dispatcher a rough age for the house and we route someone who knows that era of plumbing.
Crawlspace freezes, attic lines, and slab leaks in houses of every age.
Leaks that cross into a neighbor's unit, where fast shutoff and documentation both matter.
The same contractor network reaches the suburbs around South Houston.
